Guitar pedal order builder
Add the pedals on your board - in any order - and get them sorted into the right signal chain, with the reason for every position.
Type a model name (e.g. “Tube Screamer”) if you like. Two of the same type? List the lower-gain one first.
- 1Tuner
First, so it reads your guitar's untouched signal - and its mute switch silences the whole board.
- 2Compressor
Early, to even out your picking before anything else reacts to it. After drives it would squash their noise up too.
- 3Overdrive
Lower-gain drives before higher-gain ones: each stage feeds the next, so the order sets which one shapes the tone.
- 4Delay
Near the end, so each echo repeats your finished tone instead of being distorted into mush.
- 5Reverb
Last of the effects - it's the room your whole tone is played in.
Order sorted. Now the settings: ToneMirror tells you how to set each of these pedals - and your amp - for any song you want to play.
Get pedal settings for a songThe standard pedal order
The builder follows the order most players and builders start from: dynamics and filters first, gain in the middle, time-based effects last. Here it is in full:
- 1
Tuner
First, so it reads your guitar's untouched signal - and its mute switch silences the whole board.
- 2
Compressor
Early, to even out your picking before anything else reacts to it. After drives it would squash their noise up too.
- 3
Wah / envelope filter
Before the drives, so the filter sweeps a clean signal and the drive amplifies the sweep - the classic wah sound.
- 4
Octave / pitch shifter
Pitch trackers need a clean, simple signal to follow. Put them before anything that adds harmonics.
- 5
Boost
Before the drives, a boost pushes them (and the amp) into more saturation. Want it as a solo volume lift instead? Move it after the drives.
- 6
Overdrive
Lower-gain drives before higher-gain ones: each stage feeds the next, so the order sets which one shapes the tone.
- 7
Distortion
After lighter overdrives - stacking low gain into high gain stays tighter than the other way round.
- 8
Fuzz
Usually the highest-gain pedal, so it closes the drive section. A vintage-style fuzz (Fuzz Face, Tone Bender) is the exception - it wants your pickups directly, so tick "vintage fuzz" to move it to the front.
- 9
EQ
After the drives to shape the distorted tone, or move it before them to change what hits them.
- 10
Noise gate
After the drives, because that's where the hiss is made - gating before them lets the noise straight back in.
- 11
Chorus / phaser / flanger
After the drives, so distortion doesn't smear the sweep. (Some players put a phaser before drive for a vintage sound.)
- 12
Tremolo / vibe
Late in the chain, so the volume pulses apply to the whole tone rather than being flattened by drive.
- 13
Volume pedal
After the drives, it fades your level without cleaning up the tone - and before the delay, so echoes ring out as you fade.
- 14
Delay
Near the end, so each echo repeats your finished tone instead of being distorted into mush.
- 15
Reverb
Last of the effects - it's the room your whole tone is played in.
- 16
Looper
Very last, so it records everything you hear, effects and all.
Why each slot works - and when to break the rules - is in the full guitar pedal order guide.
Pedal order - FAQ
What is the correct order for guitar pedals?
The conventional order is: tuner, compressor, wah or filter, pitch effects, then the drives from lowest gain to highest - boost, overdrive, distortion, fuzz - then EQ, noise gate, modulation (chorus, phaser, flanger), tremolo, volume pedal, delay, reverb and looper. Dynamics and filters come first, gain in the middle, and time-based effects last. A vintage-style fuzz is the exception: it goes first of all.
Should delay go before or after distortion?
After. Delay before distortion means every echo gets distorted along with your playing, which turns into mush. After the drives, each repeat is a clean copy of your finished tone.
Where does a wah pedal go?
Usually before your drive pedals, so the drive amplifies the wah's sweep. The main exception is a vintage germanium fuzz, which often needs to come before the wah.
When should I use my amp's effects loop?
When your distortion comes from the amp's own preamp. Modulation, delay and reverb belong after the distortion, and on an amp that distorts in the preamp, the effects loop is the only place that is after it.
Is there a wrong way to order pedals?
No rule is absolute - some famous sounds come from breaking them (a phaser before the drive, or fuzz after a wah). The standard order is the reliable starting point; move one pedal at a time and listen.
Go deeper
- Settings explained9 min read
Guitar Pedal Order: How to Chain Your Pedals the Right Way
The standard guitar pedal order - tuner, compressor, wah, drive, modulation, delay, reverb - why it works, when to break it, and how the effects loop fits in.
Read the guide - GainBassMidTrebleStart here9 min read
How to Match Any Guitar Tone From a Song to Your Own Gear
A step-by-step method for getting a recorded guitar tone out of the rig you own: find the original settings, translate them for your gear, then fine-tune by ear.
Read the guide - Gear & modelers9 min read
How to Dial In Song Tones on a Modeler: Katana, Helix, Spark and More
How to rebuild a recorded guitar tone on a modeling amp or multi-effects: the right amp model and cab, block order, and the settings that matter.
Read the guide - GainBassMidTrebleSettings explained10 min read
Guitar Amp Settings Explained: Gain, Bass, Mid, Treble and Presence
What each amp knob really does, how they interact, and the median settings behind thousands of recorded guitar tones - so you can dial in faster.
Read the guide















