Guitar Amp Settings Explained: Gain, Bass, Mid, Treble and Presence

What each amp knob really does, how they interact, and the median settings behind thousands of recorded guitar tones - so you can dial in faster.

Works with any guitar, bass, amp or modeler.

By the ToneMirror team · Updated

In this guide · 10 sections
  1. 1What the numbers on an amp actually mean
  2. 2Gain: distortion, compression and sustain
  3. 3Bass, mid and treble: how the tone stack works
  4. 4Presence, resonance and the power-amp controls
  5. 5Channel volume vs master volume
  6. 6How to dial in an amp, in order
  7. 7Starting points by style
  8. 8The shortcut: settings for a specific song, on your amp
  9. 9Songs to try it on
  10. 10FAQ
The short answer

Gain sets how hard the preamp is driven - how much distortion, compression and sustain you get. Bass, mid and treble form an interactive tone stack that shapes the low end, the body and the bite. Presence adds upper treble in the power amp, and master volume sets loudness without changing the preamp's distortion. Start every knob at noon, set the gain first, then mids, bass, treble and presence, and judge it at playing volume.

  • Knob numbers are relative: 5 on one amp's gain is clean, on another it's crunch.
  • Gain adds distortion and compression - past a point it takes away punch and clarity.
  • The tone stack is passive and interactive: all knobs on 5 isn't flat, and moving one shifts the others.
  • Presence works in the power amp and lifts the upper treble the treble knob doesn't reach.
  • Set the gain for the sound and the master for the room, and dial in at the volume you'll play at.

What the numbers on an amp actually mean

An amp's knobs aren't calibrated. A “6” is just a position on a potentiometer, and what it does depends on the circuit behind it: how much gain the preamp has, how the tone stack is voiced, and the knob's taper - many gain and volume controls do most of their work in the first half of their travel. So a setting copied from one amp to another tells you less than it seems to.

What the numbers do tell you is shape: which controls are up, which are down, and roughly how far apart they are. Here is the shape of a typical recorded guitar tone:

The median guitar tone
Across 55,000+ recorded guitar tones with documented amp settings
Gain6.5
range 0–10
Bass5.5
range 2–10
Mid6
range 0–8
Treble6.5
range 1–10
Presence6
range 0–8
Volume7
range 2–10
Median of every documented setting on a 0-10 scale, with the full range under each knob.

None of the medians sits near either end of the dial. Most recorded tones live in the middle of every knob, which is why “everything at noon” is a better place to start than any preset from a forum. Set every knob straight up, then move one at a time.

Gain: distortion, compression and sustain

Gain - labeled Drive, Overdrive or, on many vintage amps, simply Volume - sets how hard the guitar signal hits the preamp. Low settings stay clean. Turning it up adds distortion, then compression and sustain, then full saturation. It also adds noise, and past a point it takes punch away: the attack of each note gets squashed and chords blur together.

GainWhat you getTypical use
0-3Clean, with headroomClean rhythm, funk, country, jazz
3-5Edge of breakup: clean when you play softly, gritty when you dig inBlues, roots rock, indie
5-7Crunch: chords still clear, notes start to sustainClassic rock, hard rock rhythm, punk
7-10High gain: compressed, saturated, long sustainMetal, modern rock leads
Rough zones for a master-volume tube amp with humbuckers. Single coils need more gain to get there; a high-gain amp gets there far sooner.

Use only as much gain as the part needs. A riff that sounds heavier on its own with more gain almost always sounds smaller in a band. For more weight, lower the gain and raise the mids, or push the amp with an overdrive set as a boost - drive low, level high - which tightens the low end instead of adding fizz.

Amps with no gain knob

On a non-master-volume amp - a vintage Marshall Plexi, a tweed or blackface Fender - one volume knob sets both how loud and how dirty the amp is, so the distortion only arrives when the amp is loud. That's why settings from records made on those amps read like “volume on 8”, and why the same knob positions on a master-volume amp at bedroom level won't sound the same.

Bass, mid and treble: how the tone stack works

The three EQ knobs together are called the tone stack. Bass shapes the low end - the thump under palm-mutes and the weight of chords. Mid covers the body of the guitar, the range where it competes with vocals and snare. Treble controls pick attack, bite and clarity. The exact frequencies vary by amp, but think of bass as around 100 Hz, mids as a few hundred hertz up to about 1 kHz, and treble as the few kilohertz above that.

Mids decide whether you're heard

The midrange is where a guitar lives in a mix. Turn the mids down and the guitar sounds big on its own, then vanishes once the bass and drums come in. Turn them up and it cuts through, at the risk of sounding honky. When a tone is great alone and lost in the band, the mid knob is the first one to move.

Why the knobs interact

On most Fender-, Marshall- and Vox-style amps the tone stack is passive: it can only cut, and 10 just means “cutting least”. The controls share one circuit, so moving one shifts the others. Turning the bass up changes how the mids sound, and on many of these amps the treble knob also sets the overall level, so turning it down makes the amp quieter as well as darker. Turn all three to zero on some of them and almost nothing comes out.

That circuit also has a mid scoop built in. With every knob on 5, a Fender-style amp isn't flat - and some Fenders, such as the Deluxe Reverb, have no mid control at all. Mids on 0 doesn't remove the midrange; it deepens a scoop that was already there.

Before or after the distortion

On most amps the tone stack comes after the preamp's gain stages, so it shapes the distorted sound much like an EQ pedal placed after a drive pedal. On a few it sits in front of the main drive stages - Mesa/Boogie's Mark series is the best-known example - so the bass knob decides how much low end gets distorted. That's why Mark-series players often run the bass very low: a setting that is merely full on a Marshall turns loose and boomy there.

Presence, resonance and the power-amp controls

Presence isn't a second treble knob. On most tube amps it works in the power amp's negative-feedback loop and lifts the upper treble, above where the treble knob mostly acts. Turn it down and the amp gets smoother and darker; turn it up and chords gain sparkle and cut - then harshness and fizz.

Resonance, also labeled Depth, does the same for the low end: it adds thump in the power amp, which is why it shows up mostly on high-gain amps built for palm-muted riffs. Both are easy to overdo, so set them for the cabinet and the room rather than for how impressive the amp sounds on its own.

  • Vox-style Cut controls work backward. On an AC30, turning the Cut knob up removes treble.
  • Many Fender-style amps have no presence knob. Some have a Bright switch instead, which adds treble mainly at lower volume settings and matters less as you turn up.
  • Set treble first, presence second. Treble for the pick attack, presence for the air on top. A bright pickup or a bright amp needs less of both.

Channel volume vs master volume

Multi-channel amps usually give each channel its own gain and its own level - labeled Volume, Level or Channel Master - plus a master that sets the output of the whole amp. They do three different jobs:

  • Gain sets the sound: how much the preamp distorts.
  • Channel volume balances the channels,so switching from rhythm to lead doesn't jump or drop in level.
  • Master sets how loud the amp is in the room. On a tube amp, turning it up also pushes the power section, adding compression and bloom.

So set the gain for the sound, set each channel's level so switching is even, and use the master for the room. If a lead is buried, raise that channel's level, not its gain - more gain makes it more compressed, not louder in the mix.

How to dial in an amp, in order

The order matters because each knob changes how the next one behaves. This sequence gets most amps close in a few minutes:

  1. 1
    Start everything at noon
    Gain, bass, mid, treble and presence on 5; master at the volume you'll play at; the guitar's volume and tone on full.
  2. 2
    Set the gain
    Strum an open chord and raise the gain until it has the grit the part needs. Stop while every string is still audible.
  3. 3
    Set the mids
    Play along with the record or a backing track. Raise the mids until the guitar sits forward; lower them if it honks.
  4. 4
    Set the bass
    Bring it up until palm-mutes thump, then back off as soon as they blur. More gain needs less bass.
  5. 5
    Set the treble, then the presence
    Treble until the pick attack is clear, presence until chords have air on top. Stop before the high end turns brittle.
  6. 6
    Re-check the gain
    EQ changes how distorted an amp sounds - more mids and treble make it grittier, more bass makes it woolly. Trim the gain and compare with the record again.

Common mistakes

  • Scooping the mids for heaviness, then disappearing in the band.
  • Turning up the gain to get louder.
  • Dialing in quietly or on headphones, then playing loud.
  • Moving three knobs at once, so you never learn which one helped.

Starting points by style

Settings shift with style, but less than you might think. Here are the typical settings behind recorded blues-rock and heavy metal guitar tones:

Typical blues-rock settings
Median across 3,100+ recorded blues-rock tones in the ToneMirror catalog
Gain5.5
range 1–8.5
Bass5
range 2–6.5
Mid6
range 4.5–8
Treble6.5
range 2–7.5
Presence6
range 0–7
Volume7
range 3–10
Each dial shows the median value on a 0-10 scale; the range under it is the lowest and highest setting in the set. A starting point to adjust by ear - not a preset.
Typical heavy metal settings
Median across 4,800+ recorded heavy metal tones in the ToneMirror catalog
Gain7
range 2.5–9
Bass5.5
range 3.5–7
Mid6
range 2.5–7.5
Treble6.5
range 5–8
Presence6
range 4.5–8
Volume7
range 5–10
Each dial shows the median value on a 0-10 scale; the range under it is the lowest and highest setting in the set. A starting point to adjust by ear - not a preset.

Put the two side by side and the biggest gap is the gain. The EQ is much closer than the “scoop the mids for metal” folklore suggests: plenty of heavy records keep their mids up so the riffs cut through. The table turns that into starting points for a range of styles.

StyleGainBassMidTreblePresencePickup
Clean pop, indie, soul1-34-55-66-75-6Neck or in-between
Funk1-34676In-between or middle
Jazz1-25-653-43-4Neck, tone rolled back
Country2-44-5676Bridge single coil
Blues4-656-765Neck or middle
Classic rock5-756-76-76Bridge humbucker
Punk and pop punk6-75-666-76Bridge humbucker
Hard rock and 80s metal6-85-666-76Bridge humbucker
Modern metal6-8, plus a boost55-66-76Bridge humbucker
Suggested starting points on a 0-10 dial for a master-volume tube amp - not measured data. Adjust the gain for your pickups and amp, then fine-tune by ear.

To hear the styles on record, open any of these and compare its settings with the table:

The free amp settings tool shows typical settings genre by genre, and the style guides go deeper: blues, classic rock, metal and clean tones. Pickup choice changes all of it - see pickup positions explained.

The shortcut: settings for a specific song, on your amp

Knowing what each knob does gets you into the right neighborhood. Getting a specific record means translating its settings for your amp's voicing, your pickups and your speaker - the part that usually takes an evening of trial and error. ToneMirror does that translation. Pick a song, enter the guitar, amp or modeler and pedals you own, and it returns the gain, EQ, presence and master positions for your amp, along with the pickup, tuning, your guitar's volume and tone, and pedal settings in signal-chain order.

Start from the tone matcher, or browse the tone library to see the settings a record was made with before you translate them.

Songs to try it on

Each of these has its recorded rig and settings on its own page - open one, then get it translated for your gear.

Frequently asked questions

What are the best amp settings for guitar?

There's no single best setting, because every amp's knobs are voiced differently. Start with every control at noon, set the gain for the amount of distortion the part needs, then adjust mids, bass, treble and presence in that order at the volume you'll play. Most recorded tones end up with every knob somewhere in the middle of its range.

What does the presence knob do on an amp?

Presence boosts the upper treble in the power amp, usually through the negative-feedback loop, above the range the treble knob covers. It adds air, sparkle and cut; too much makes the amp harsh and fizzy. Set the treble first, then the presence.

Is gain the same as volume?

No. Gain sets how hard the preamp is driven - how much distortion and compression you get - while master volume sets how loud the amp is. On older amps with no master volume, one knob does both, which is why those amps only distort when they're loud.

Should I scoop the mids?

Rarely all the way. A mid scoop sounds big when you play alone, but the midrange is where a guitar sits in a band, so a deeply scooped tone tends to disappear once bass and drums come in. A heavy sound usually comes from tight bass and a moderate mid cut, not mids on zero.

Why does my amp sound different at low volume?

Human hearing is less sensitive to bass and treble at quiet levels, and a tube amp's power section and speaker only compress and break up when they're pushed. So a quiet tone sounds thinner and less alive, and EQ set quietly is usually too bassy and bright once you turn up.

Is there a tool that gives amp settings for a specific song?

Yes. ToneMirror takes a song and the gear you own - guitar, amp or modeler, and pedals - and returns amp settings, pickup position, tuning, guitar knob settings and pedal settings adapted to your rig. For genre-wide starting points, its free amp settings tool shows typical settings by genre.

Get settings for my rig