Guitar tone glossary
70 amp, pickup, pedal, tuning and modeler terms in plain English - what each one is, and what it means for getting a song's tone.
Skip the theory - get the settings for any song on your gear.
Amps and amp settings
- Gain
- Gain is how hard the amp's preamp is driven - turned up, the signal clips into distortion, compression and sustain. It sets how much distortion you get far more than the volume does, and most players use more of it than the records they are copying.
- Amp settings explained →
- Master volume
- The master volume sets how loud the amp is after the preamp, without changing how much preamp distortion you get. A master-volume amp can sound distorted at low volume; an amp without one only distorts when it is loud.
- Tone at low volume →
- Preamp
- The preamp is the first stage of an amp: it boosts the guitar's signal, shapes it with the tone controls and, when pushed, creates most of a high-gain amp's distortion.
- Power amp
- The power amp turns the preamp's signal into enough power to drive the speaker. Pushed hard, its tubes add a compressed, fat distortion - the sound of a cranked vintage amp - which is different from preamp gain.
- Headroom
- Headroom is how loud an amp can play before it starts to distort. High-headroom amps stay clean at volume and suit pedal platforms and clean tones; low-headroom amps break up early.
- Clean tone guide →
- Edge of breakup
- Edge of breakup is an amp set so it is clean when you play softly and gritty when you dig in. It is the core of a lot of blues and classic rock, and it puts the guitar's volume knob and your picking in charge of the distortion.
- Blues tone guide →
- Tone stack
- The tone stack is the amp's bass, middle and treble circuit. Its controls interact rather than acting like a graphic EQ, and every amp design centers them differently - which is why the same knob numbers sound different on two amps.
- Mids
- The mid control shapes the middle of the guitar's range, where it sits in a band mix. Mids up make a guitar forward and vocal; mids down make it scooped and heavy on its own but easier to lose behind the drums and bass.
- Scooped mids
- A scooped tone has the mids turned well below the bass and treble. It sounds huge alone and was common in some 80s and 90s metal, but it is the first thing to fix when a guitar disappears in a band mix.
- Metal tone guide →
- Presence
- Presence boosts the upper treble in the power amp - the edge and air above the treble control. A little helps a guitar cut; too much adds fizz and harshness, especially with distortion.
- Resonance
- Resonance (sometimes called depth) boosts the low end in the power amp, adding thump to palm mutes. It is most common on high-gain amps and modelers, and easy to overdo at home volume.
- Bright switch
- A bright switch adds treble that is most noticeable at low volume settings. It suits dark guitars and clean tones, and is often switched off as the amp gets louder.
- Sag
- Sag is the slight compression and softening when a tube amp's power supply struggles under a hard-hit chord. It gives vintage amps their spongy feel; modelers often have a sag control to imitate it.
- Cabinet
- The cabinet (cab) is the speaker enclosure, and with the speaker inside it shapes the tone as much as any knob. Open-back cabs sound airy and wide; closed-back cabs are tighter with more low end.
- Attenuator
- An attenuator sits between an amp and its speaker and turns the volume down after the power amp, so a cranked tube amp's power-tube distortion is available at lower volume.
- Tone at low volume →
Guitars and pickups
- Single-coil pickup
- A single-coil pickup has one coil of wire. It sounds bright, clear and articulate - the Strat and Tele sound - and picks up some hum.
- Pickup positions explained →
- Humbucker
- A humbucker has two coils wired to cancel hum. It is louder and thicker than a single coil, pushes an amp harder, and is the standard pickup for hard rock and metal.
- Pickup positions explained →
- P-90
- A P-90 is a wide single-coil pickup - louder and grittier than a Strat-style single coil, brighter than a humbucker.
- Pickup output
- Pickup output is how strong a signal the pickup sends to the amp. Higher-output pickups drive an amp into distortion sooner, so the same amp settings sound dirtier with them.
- Pickup position
- The pickup position is which pickup (or combination) is selected. The bridge pickup is bright and tight, the neck pickup warm and round, and in-between positions on a Strat-style guitar hollow and glassy.
- Pickup positions explained →
- 5-way switch
- A 5-way switch, standard on Strat-style guitars, selects bridge, bridge and middle, middle, middle and neck, or neck. Positions 2 and 4 are the 'in-between' sounds used for funk and clean parts.
- Coil split
- A coil split turns a humbucker into a single coil by switching one of its coils off. It gives a brighter, thinner sound and brings back some hum.
- Woman tone
- Woman tone is a smooth, singing lead sound from the neck pickup with the guitar's tone knob rolled almost all the way down into a driven amp, famously used by Eric Clapton in Cream.
- Scale length
- Scale length is the vibrating length of the string from nut to saddle. Longer scales (like a Strat's) feel tighter and sound brighter; shorter scales (like a Les Paul's) feel slinkier and sound warmer.
- String gauge
- String gauge is the thickness of the strings. Heavier strings sound fuller and hold pitch better in low tunings; lighter strings are easier to bend.
- Tunings guide →
- Intonation
- Intonation is whether notes play in tune all the way up the neck. Check it after changing string gauge or tuning: the 12th-fret harmonic and fretted note should match.
Pedals and effects
- Overdrive
- An overdrive pedal adds smooth, amp-like distortion and is often used as a boost into an already dirty amp to tighten it up. The Tube Screamer is the classic example.
- Overdrive pedal settings →
- Distortion
- A distortion pedal adds heavier, more saturated clipping than an overdrive, often with more compression and a stronger EQ character.
- Distortion pedal settings →
- Fuzz
- A fuzz pedal clips the signal into a thick, square, buzzing distortion - the sound of 60s psychedelia, stoner rock and Big Muff walls of sound.
- Fuzz pedal settings →
- Boost
- A boost raises the signal level, either to push an amp into more distortion or to lift the volume for a solo. Treble boosters lift the upper mids as they boost.
- Overdrive and boost settings →
- Compressor
- A compressor evens out the difference between loud and quiet notes, adding sustain and a smooth, even attack. It is a staple of country, funk and clean parts.
- Compressor settings →
- Wah
- A wah pedal sweeps a resonant filter across the frequency range as you rock it, giving a vocal 'wah' sound.
- How to use a wah →
- Envelope filter
- An envelope filter is an auto-wah: the filter sweeps with how hard you play rather than with your foot. It is a funk and bass staple.
- Funk tone guide →
- Chorus
- Chorus mixes your signal with a slightly delayed, pitch-wobbled copy, making one guitar sound shimmery and wide. It is the sound of 80s cleans and many grunge verses.
- Modulation settings →
- Phaser
- A phaser sweeps notches through the frequency range, creating a swirling, whooshing movement. The MXR Phase 90 is the classic.
- Modulation settings →
- Flanger
- A flanger mixes in a very short, sweeping delay with feedback for a metallic, jet-plane whoosh - more intense than a phaser.
- Modulation settings →
- Uni-Vibe
- A Uni-Vibe is a throbbing, chorus-like phase effect originally built to imitate a rotating speaker, famous on Jimi Hendrix's live recordings.
- Modulation settings →
- Tremolo
- Tremolo rhythmically varies the volume. Many vintage amps have it built in (sometimes confusingly labelled 'vibrato').
- Modulation settings →
- Delay
- Delay repeats what you play after a set time. Its main controls are time (how long until the repeat), feedback (how many repeats) and mix (how loud they are).
- Delay settings →Delay calculator →
- Slapback
- Slapback is a single, short, unsynced delay repeat - roughly 80 to 150 milliseconds - that gives rockabilly and country guitar its snap.
- Delay settings →Country tone guide →
- Dotted-eighth delay
- A dotted-eighth delay sets the repeat to three quarters of a beat, so straight eighth notes and their echoes interlock into a rhythmic pattern - the sound of many U2 records.
- Delay calculator →
- Tape echo
- Tape echo is a delay made by recording onto a moving tape loop. Its repeats are warm, slightly wobbly and darken as they fade; many delay pedals imitate it.
- Delay settings →
- Reverb
- Reverb simulates the reflections of a room or space, adding depth and ambience. Spring, plate, room and hall are the common types.
- Reverb settings →
- Spring reverb
- Spring reverb comes from sending the signal through metal springs, as in many classic amps. It has a bouncy, splashy sound - the 'drip' of surf guitar.
- Reverb settings →
- Plate reverb
- Plate reverb was made by vibrating a large metal plate in a studio. It is smooth and dense, and common on recorded vocals and guitars.
- Reverb settings →
- Pre-delay
- Pre-delay is a short gap before a reverb starts. It keeps the attack of each note clear while still adding space.
- Noise gate
- A noise gate mutes the signal when you stop playing, cutting hiss and hum. High-gain players use one for tight, silent stops between riffs.
- Modern metal tone →
- Octave pedal
- An octave pedal adds a note an octave below or above what you play, for a bigger or organ-like sound.
- True bypass
- A true-bypass pedal passes the signal straight through untouched when it is off. Many true-bypass pedals in a row can dull the tone over long cables.
- Buffer
- A buffer is a circuit that keeps the guitar's signal strong over long cable runs. Some vintage fuzzes misbehave after one, which is why they often go first on a board.
- Signal chain
- The signal chain is the order the guitar's signal passes through pedals and the amp. The usual order is tuner, compressor, wah, drive, modulation, delay, reverb.
- Pedal order guide →Pedal order builder →
- Effects loop
- An effects loop is a send and return between an amp's preamp and power amp. Delay, reverb and modulation go there when the distortion comes from the amp's preamp.
- Stacking
- Stacking means running one drive pedal into another. Usually the lower-gain pedal goes first so it shapes what the higher-gain one sees.
- Overdrive pedal settings →
Tunings
- Standard tuning
- Standard tuning is E A D G B E from the lowest string to the highest. Most songs are written in it, but many famous records are tuned lower.
- Online tuner →
- E♭ standard
- E♭ standard (half step down) tunes every string down one semitone, keeping every chord shape the same. Jimi Hendrix, Stevie Ray Vaughan and Slash recorded much of their best-known music in it.
- Songs in E♭ standard →
- Drop D
- Drop D tunes only the low E string down to D, so a power chord on the bottom three strings is one finger.
- Songs in drop D →
- Drop C
- Drop C is D standard with the low string dropped a further whole step to C - a staple of metalcore and nu metal.
- Songs in drop C →
- Open tuning
- In an open tuning the unfretted strings ring a chord, so one finger barred across the neck plays a chord anywhere - the basis of most slide guitar.
- Songs in open G →
- Baritone guitar
- A baritone guitar has a longer scale built for low tunings like B or A, keeping the strings tight where a standard guitar would go slack.
- Modern metal tone →
Recording and modeling
- Double-tracking
- Double-tracking records the same part twice and pans the takes left and right. It is why a record's rhythm guitar sounds bigger than one guitar in a room.
- Why you don't sound like the record →
- DI
- A DI (direct input) records an instrument straight into the desk without a mic'd amp. Bass is often recorded this way, alone or blended with an amp.
- Bass tone guide →
- Equal-loudness effect
- The ear hears less bass and treble at low volume than at high volume (the Fletcher-Munson curves), so a tone dialled in quietly sounds boomy and harsh when turned up.
- Tone at low volume →
- Modeler
- A modeler is a digital amp and effects unit - such as a Boss Katana, Line 6 Helix or Positive Grid Spark - that recreates many amps and pedals in software.
- Modeler settings for songs →
- Profile or capture
- A profile or capture is a snapshot of one real amp at one setting, played back by units like the Kemper, Quad Cortex and TONEX. Choose one captured near the gain you need.
- Kemper settings →Quad Cortex settings →
- Impulse response (IR)
- An impulse response is a recording of how a speaker cabinet and mic colour sound, loaded into a modeler or IR loader to replace a real cab.
- Block
- A block is one amp, cab or effect in a modeler's signal chain. The order of the blocks is the routing, just like the order of pedals on a board.
- Modeler guide →
- FRFR
- FRFR (full range, flat response) speakers reproduce a modeler's output without adding a guitar speaker's colour, so the cab simulation does that job instead.
- Unity gain
- Unity gain means a block or pedal is as loud switched on as off. Keeping blocks at unity stops patches jumping in volume and keeps a tone's balance with the band.
- Modeler guide →
- Tone matching
- Tone matching is getting a recorded song's guitar or bass tone out of different gear by translating the original settings for your guitar, amp and pedals rather than copying them.
- How to match a tone →Tone matcher →