Bass7 min read

Metal Bass Tone Settings: Grind, Clank and a Solid Low End

How to get a metal bass tone: blending clean lows with distortion, pick attack and clank, tuning down with the guitars, compression, and EQ that cuts through.

Works with any guitar, bass, amp or modeler.

By the ToneMirror team · Updated

In this guide · 10 sections
  1. 1Blend the distortion: clean lows, driven mids and highs
  2. 2EQ for metal bass: upper mids, not more lows
  3. 3Pick attack, clank and fingers
  4. 4Tune down with the guitars
  5. 5Compression, and filtering the dirt
  6. 6Stay out of the guitars' way
  7. 7DI, amp or plugin: recording and playing live
  8. 8The shortcut: metal bass settings for your rig
  9. 9Songs to try it on
  10. 10FAQ
The short answer

For a metal bass tone, keep the low end clean and distort only the mids and highs - with a blend knob or two parallel signals - then boost the upper mids around 800Hz-1.5kHz so the bass cuts between the guitars instead of adding more lows. Play with a pick or hard fingers for attack and clank, tune down with the guitars, compress firmly, and high-pass the distorted signal so it never smears the bottom.

  • Distort the mids and highs, not the lows: blend a clean low end under the dirt.
  • Upper mids make metal bass audible; more lows only make the mix muddier.
  • A pick or hard fingers near the bridge, on fresh roundwounds, gives the clank that reads through guitars.
  • Tune with the guitars, and go up a gauge - or to a five-string - when they drop.
  • High-pass the distorted signal around 200-400Hz and low-pass it around 3-5kHz to keep it tight and fizz-free.

Blend the distortion: clean lows, driven mids and highs

Put a bass straight through a distortion pedal and the low end collapses. Distortion compresses the signal and piles harmonics on top of the fundamental, so the lows lose their punch and the bottom of each note smears into a buzz - while two low-tuned, high-gain guitars are already crowding the low mids. The result is a bass that manages to sound muddy and thin at the same time.

The fix nearly every modern metal bass tone uses is to split the job. One signal stays clean and carries the low end - the weight you feel under the kick drum. A second signal is distorted and carries the growl, grind and attack that let the bass be heard. Blend the two and the bass keeps its floor while sounding as aggressive as the guitars.

SetupHow it worksGood for
Drive pedal with a blend knobMixes your clean signal back in under the dirtThe simplest start; most bass drives have one
Crossover drive or preampSplits by frequency: the lows stay clean, only the upper range is distortedA tight, modern tone with no mud
Two amps or two channelsOne clean, one driven, blended at the deskBig stages and studios
Parallel path in a DAW or modelerOne DI split into a clean track and a distorted one, each filteredRecording and playing at home
Four routes to the same idea. When you blend two paths, check the phase: if the low end gets weaker as the dirt comes in, flip the polarity of one.

Tool's Justin Chancellor is the best-known example: his rig splits the bass between a clean amp for the fundamental and a driven one for the attack, which is how parts like “Fear Inoculum” sound round and abrasive at once.

Starting points

  • Blend: 30-50% wet for grind underneath the band, 50-70% for an obviously distorted tone.
  • Drive: lower than feels right on its own. With the clean lows underneath, a moderate drive sounds heavier than it is.
  • Level: set so switching the dirt on changes the character, not the volume.

EQ for metal bass: upper mids, not more lows

When the guitars are tuned low and heavily distorted, adding low end to the bass doesn't make the band heavier - it makes the mix muddier. The weight in a metal mix comes from the bass and kick sharing the bottom cleanly. What makes the bass audible is its upper midrange, where the grind and attack sit just above the guitars' thick low mids.

RangeWhat it doesSuggested move
Lows, 40-100HzWeight and punch under the kickKeep solid, boost little; the clean path supplies it
Low mids, 200-400HzMud - where low-tuned guitars pile upCut a few dB
Mids, 500-800HzBody and honkFlat, or a small cut if it honks
Upper mids, 800Hz-1.5kHzGrind and note definitionBoost - this is where the bass is heard
Presence, 2-4kHzPick attack and clankTo taste; it competes with the guitars' bite
Above 5kHzFizz on the distorted pathLow-pass the dirt here
Approximate ranges and suggested moves - adjust by ear with the guitars playing.

For a reality check, here is where recorded metal bass parts sit. The gain is moderate rather than saturated, and the mids sit up with the bass instead of scooped - the opposite of what most players dial in when they want “heavy”.

Typical heavy metal, thrash, metalcore and prog metal bass settings
Median across 620+ recorded metal bass tones in the ToneMirror catalog
Gain4.5
range 1.5–8
Bass6.5
range 0–7
Mid6.5
range 4.5–10
Treble6
range 0–8.5
Presence5
range 4–8
Volume8
range 6–10
Each dial shows the median value on a 0-10 scale; the range under it is the lowest and highest setting in the set. A starting point to adjust by ear - not a preset.

Treat the numbers as a shape to aim for on your own amp, not a preset. Every bass amp centers its controls on different frequencies; the bass tone settings guide explains how to read them.

Pick attack, clank and fingers

Metal bass gets its definition from the attack as much as from the EQ. A pick gives a hard, bright transient that cuts through distortion and locks to the guitars' picking, which is why so much thrash and modern metal bass is played with one. Use a thick pick, play nearer the bridge for a tighter tone, and dig in evenly - a compressor can't rescue uneven downstrokes.

Clank is the sound of the string hitting the frets: bright, metallic, almost a click on every note. It comes from a hard attack, fresh roundwounds (stainless steel is the clankiest), fairly low action, and enough treble or presence to let it through. Some styles feature it; others keep it down so it doesn't fight the guitars' pick attack.

Fingers can be just as heavy

  • Steve Harrisplays Iron Maiden's galloping lines with his fingers, hard, with the treble up so every note clanks - on flatwounds, which shows how much of clank is in the hands. Hear it on “The Trooper”.
  • Cliff Burton played fingerstyle too, and put his bass through distortion and a wah for the intro of “For Whom the Bell Tolls” - often mistaken for a guitar.
  • Lemmy went the other way: a pick, chords, and a Marshall turned up like a guitar amp, as on “Ace of Spades”.

Tune down with the guitars

When the guitars drop, the bass drops with them - or every riff is a half or whole step off. The three most common bass tunings mirror the guitar ones:

  • E♭ standard - every string down a half step, common in classic metal and thrash. See bass songs in E♭.
  • Drop D - only the low E drops, to a D around 37Hz, for riffs built on the open low string. See bass songs in drop D.
  • D standard - everything a whole step down, slacker and darker. See bass songs in D standard.
  • Drop C and lower - on a four-string, drop C is C G C F. For drop B and below, most players use a five-string with a low B (about 31Hz) rather than dragging a four-string down until it flops.

The lower you tune, the less of the fundamental anyone actually hears: a low B sits near the bottom of what bass cabs and PAs reproduce well. So the deeper the tuning, the more the bass depends on its upper harmonics to be heard - another reason the upper mids matter more than extra lows.

TuningTypical gauge (34-inch scale)
E standard, E♭ standard45-105
Drop D, D standard45-105 to 50-110
Drop C, C standard (four-string)50-110 to 55-110, or heavier
Drop B and lowerA five-string with a 130-135 low B, or a dedicated low-tuning set
Common starting points. Have the nut slots and intonation checked after a big jump in gauge.

Compression, and filtering the dirt

Compression

Metal bass is usually compressed firmly. Under walls of guitar, any note that dips in level vanishes, and fast picked lines vary more than you would think. Distortion already compresses the dirty path, so aim the compressor at the clean signal - or at the whole bass, before the split.

  • Ratio 4:1 to 8:1, with around 4-8dB of gain reduction on the hardest notes.
  • Attack medium, roughly 10-30ms, so the pick transient gets through before the compressor clamps down.
  • Release medium, so the compressor recovers between fast notes instead of pumping.
  • Placement: before the drive, so the distortion sees an even signal and grinds consistently.

High-pass the dirt, low-pass the fizz

The most useful filter in metal bass is a high-pass in front of the distortion, somewhere around 200-400Hz - wherever your blend sounds tight. The distortion then never sees the low end, so it can't smear it; the clean path supplies the lows instead. After the distortion, a low-pass around 3-5kHz removes the fizzy, crackling top that distorted bass produces and that clashes with the guitars. Crossover drives do both of these for you; with a simple blend pedal, an EQ pedal after it can handle the top.

  1. Guitar
  2. Tuner
  3. Compressor
  4. Blend or crossover drive
  5. EQ: low-mid cut, upper-mid boost
  6. Amp
A simple metal bass board. The drive's blend or crossover keeps the lows clean; the EQ after it carves the low mids and trims fizz. A starting point, not a rule.

Stay out of the guitars' way

Metal mixes are crowded: two or more distorted guitars, a clicky kick drum, cymbals and vocals. The bass gets a clear lane only if it steps back where the guitars are strongest.

  • Cut the low mids on the bass, too. Around 200-400Hz is where low-tuned guitars are thickest and where most mud lives. Carving it on both instruments clears more than doing either alone.
  • Own the very bottom. Metal guitars are usually high-passed around 80-100Hz, so the range below is yours, and a tight, clicky metal kick leaves much of it free. The metal guitar guide covers that side.
  • Match the note lengths. When the guitars palm-mute, stop your notes with them. A bass note ringing under a muted chug blurs the riff more than any EQ can.
  • Pick a role for each section. Doubling the riff tightly, holding long roots under fast guitar picking, or moving to a melodic line all work - just not all at once.
  • Don't fight for the bite.If your clank sits right on top of the guitars' pick attack at 2-4kHz, one of you should give way - usually the bass, by low-passing the dirty path.

Above all, check the tone with the whole band playing. A bass that sounds massive alone almost always needs fewer lows and more upper mids at rehearsal.

DI, amp or plugin: recording and playing live

Most metal bass on modern records starts with a clean DI, whatever else is used. A DI captures the bass exactly, so the distorted side can be added or changed later - through an amp, a preamp pedal or a plugin - without replaying the part, which is called reamping.

  • At home: DI into your interface and duplicate the track. Low-pass the clean copy somewhere around 150-300Hz, high-pass the other, distort it with an amp sim or plugin, and compress the two together.
  • On a modeler: on units that can split a signal path, such as the Helix, build a clean branch and a drive or amp branch and mix them at the end. See the modeler pages for your unit.
  • Live: send the PA a clean DI and a dirty one - many bass preamp pedals have their own DI output - or one blended signal. Your stage amp is for you; the DI is what the audience hears.

Whatever the route, judge it against the guitars, not on its own. For a heavier angle than the classic parts linked above, study these groove and extreme metal bass parts:

The shortcut: metal bass settings for your rig

A specific record - a Maiden gallop, a Tool riff, a drop-tuned breakdown - has its own bass, amp, tuning and drive, and the settings that get you there depend on what you own. ToneMirror starts from what was used on the recording and translates it for your bass, amp or modeler and pedals: EQ for your amp, the pickup, the tuning, and drive and compressor settings in signal-chain order, including how to set a blend if your pedal has one.

On a modeler, it lays out the blocks to build. Start from the tone matcher, or browse the tone library for the bass part you want.

Songs to try it on

Each of these has its recorded rig and settings on its own page - open one, then get it translated for your gear.

Frequently asked questions

How do I get a good metal bass tone?

Blend a clean low end with distortion on the mids and highs, boost the upper mids around 800Hz-1.5kHz, cut the low mids where the guitars pile up, and compress firmly. Play with a pick or hard fingers on fresh roundwounds, and tune down with the guitars.

Should metal bass be distorted?

Usually partly. A fully distorted bass loses its low end, so most metal tones blend a clean signal for the lows with a distorted one for grind and attack. How much depends on the style: classic metal bass is often mostly clean and bright, while modern metal and djent tend to blend in heavier distortion.

Pick or fingers for metal bass?

Either works. A pick gives a hard, bright attack that cuts through distorted guitars and locks to their picking, which is why so much thrash and modern metal uses one. Hard fingerstyle near the bridge can be just as aggressive - Steve Harris and Cliff Burton both played with their fingers.

What is the best EQ for metal bass?

Cut a few dB in the low mids (200-400Hz), boost the upper mids (800Hz-1.5kHz) for definition, keep the lows solid but not boosted, and add 2-4kHz only as far as the clank needs. Low-pass the distorted signal around 3-5kHz to remove fizz.

What tuning should a metal bassist use?

Whatever the guitarists use - E flat standard, drop D, D standard and drop C are common, and modern metal often goes lower. For drop B and below, most bassists use a five-string with a low B rather than slackening a four-string, and heavier strings keep lower tunings tight.

Is there an app that gives metal bass settings for a specific song?

Yes - ToneMirror translates a recorded bass tone to the gear you own. Pick the song, enter your bass, amp or modeler and pedals, and it returns EQ, pickup, tuning and drive settings for your rig, including how to set a blend.

Get my bass settings