80s Rock and Hair Metal Guitar Tone: Settings That Still Work

How to get an 80s rock and hair metal guitar tone: hot-rodded Marshall-style crunch, humbuckers, locking trems, chorus and delay for solos, and stacked doubles.

Works with any guitar, bass, amp or modeler.

By the ToneMirror team · Updated

In this guide · 10 sections
  1. 1Where the 80s sound came from: hot-rodded and master-volume amps
  2. 2Amp settings: hot crunch, mids up, bright presence
  3. 3Superstrats, humbuckers and locking trems
  4. 4Chorus and delay: the sound of 80s cleans and solos
  5. 5Stereo racks, gates and compression, briefly
  6. 6E♭ tuning and the techniques that sell it
  7. 7Why the records sound so big: stacked doubles
  8. 8The shortcut: an 80s song's settings for your rig
  9. 9Songs to try it on
  10. 10FAQ
The short answer

For an 80s rock or hair metal tone, play a bridge humbucker into a Marshall-style amp with more gain than 70s crunch but far less than modern metal - gain around 6 to 7, mids around 6, bass moderate, treble and presence a little above noon. Push the amp with an overdrive if it runs out of gain, add chorus and delay to clean intros and solos, check for E♭ tuning, and double the rhythm parts.

  • 80s rock gain came from hot-rodded and master-volume amps - more than 70s crunch, far less than modern metal.
  • Keep the mids up and the presence bright; the deep scoop belongs to thrash, not hair metal.
  • Superstrats with a hot bridge humbucker and a locking trem defined the look, but Les Pauls into Marshalls never left.
  • Chorus and delay are the decade's signature effects - on clean intros and solos, rarely on the main riff.
  • The records sound huge because rhythm parts were doubled and stacked, not because one amp was maxed.

Where the 80s sound came from: hot-rodded and master-volume amps

The 70s got its crunch by turning a non-master-volume amp all the way up. In the 80s players wanted more - more sustain, more saturation, solos that sang - at volumes a club could survive. Two things delivered it: amp techs hot-rodding Marshalls with an extra preamp gain stage, and factory master-volume amps that moved the distortion into the preamp.

Eddie Van Halen's 1978 debut set the template the decade chased: a homemade Strat-style guitar with a single bridge humbucker into a cranked 100-watt Marshall, with an MXR Phase 90 for color. From there the gear got hotter. Marshall's master-volume JCM800 heads arrived in 1981 and became the default rock amp of the decade, Mesa/Boogie's Mark series offered cascading high gain, and the Soldano SLO-100 (1987) set a new bar for smooth, saturated lead tone.

The decade's rock splits into two broad sounds that overlap constantly:

SoundArena rockHair metal
GainModerate crunch, polishedHotter and more saturated, long sustain
EQMids forward, smooth topMids up, bright presence
GuitarsLes Pauls, Strats and superstratsSuperstrats with locking trems, Les Pauls
EffectsChorus and delay, used sparinglyChorus and delay on solos, phaser, flanger
Hear it inJourney, Foreigner, SurvivorDef Leppard, Ratt, Mötley Crüe, Bon Jovi
Broad strokes - each tone page lists what the specific recording used.

The cranked-amp sound of the decade before - and the era's fuzz, wah and treble boosters - is covered in the classic rock tone guide.

Amp settings: hot crunch, mids up, bright presence

80s rock tone is a mid-forward, fairly bright crunch with enough gain to sustain a solo. These are the medians across the hair metal and arena rock guitar tones we have documented:

Typical hair metal and arena rock settings
Median across 1,700+ recorded glam metal and arena rock tones in the ToneMirror catalog
Gain6.5
range 3–8.5
Bass5.5
range 4–6.5
Mid6
range 5–7
Treble6.5
range 5–8
Presence6
range 4–7
Volume7
range 5–9
Each dial shows the median value on a 0-10 scale; the range under it is the lowest and highest setting in the set. A starting point to adjust by ear - not a preset.

Read it as a shape: gain past halfway but well short of the top, mids at or above noon, bass near the middle, treble and presence a notch above center. That is hotter than classic rock and nowhere near a scooped thrash tone. If any of the knob names are unfamiliar, the tone glossary defines them.

On a Marshall-style master-volume amp

  • On a JCM800-style head the preamp volume is the gain control. Rhythm parts usually sit past halfway, leads a little higher; the master sets loudness.
  • Start with mids 6 to 7, bass 4 to 5, treble 6 to 7 and presence around 6, then adjust by ear.
  • Keep the bass a touch lower than feels right alone. A 4x12 at volume adds plenty, and too much makes the palm-muted chugs flub.

When your amp runs out of gain

If your amp tops out at classic-rock crunch, put an overdrive in front - drive low to noon, level up, tone around noon. That is the hot-rod mod in a box: the pedal pushes the preamp harder and tightens the low end. The overdrive pedal settings guide has the details. On a modeler, start from a JCM800-style model for rhythm, or a Soldano- or Mark-style model for smoother leads, with the gain lower than the model invites.

Superstrats, humbuckers and locking trems

The decade's signature guitar is the superstrat: a Strat-shaped body with a hot humbucker in the bridge (often with single coils beside it), a thin, fast neck, jumbo frets and a Floyd Rose locking tremolo. Charvel, Jackson, Kramer and Ibanez built the look, and players like Richie Sambora took it onto the biggest stages.

The pickups matter more than the shape. Hot, high-output humbuckers in the mold of the DiMarzio Super Distortion and the Seymour Duncan JB hit the amp harder and push the upper mids forward, which is a big part of how the records sound bright without sounding thin.

GuitarInto a hot MarshallAdjust
Superstrat, bridge humbuckerBright, tight and cuttingTreble and presence a notch lower
Les Paul, bridge humbuckerThick and warm, more low midsTreble and presence up a notch, bass down
Strat with single coilsThinner, more hum under gainMore gain or a boost, mids up, add a gate
Suggested adjustments from the same starting settings.

The locking trem

A Floyd Rose clamps the strings at the nut and the saddles, so the guitar stays in tune through dive bombs and wild bar work. It changes the feel and a little of the decay more than the core tone - you don't need one to sound 80s, only to play the dives. If your guitar has a fixed bridge, play the parts and skip the bar tricks.

And the Les Paul never left. Slash recorded Appetite for Destructionon a Les Paul replica, and a Les Paul's bridge humbucker into a Marshall carried a good share of the decade's arena rock. The tone page for each song says which kind of guitar the record used.

Chorus and delay: the sound of 80s cleans and solos

If one effect says “80s,” it is chorus. Boss's compact CE-2 arrived in 1979 and ended up on the decade's clean intros, power-ballad arpeggios and solos. Across every recorded song we have documented - not only the 80s - chorus pedals take most of the top spots in the modulation family, led by the CE-2, with MXR's Phase 90 - Van Halen's phaser - next in line:

The chorus, phaser and flanger pedals on the most recorded tones
  1. 1Boss CE-2 Chorus1,305 tones
  2. 2MXR Phase 90318 tones
  3. 3Boss CE-2W Waza Craft Chorus156 tones
  4. 4Boss CH-1 Super Chorus65 tones
  5. 5Electro-Harmonix Stereo Electric Mistress41 tones
  6. 6Boss CE-5 Chorus Ensemble29 tones
  7. 7MXR M117R Flanger24 tones
  8. 8MXR M234 Analog Chorus21 tones
Pedals credited on the recorded tones in the ToneMirror catalog, counted per song. A model listed is the documented unit or its catalogued modern equivalent - each pedal's page has the songs.

Starting settings

EffectRate / timeDepth / repeatsMixUse it on
Chorus, clean partsSlow, 9 to 11 o'clockModerate to deepPedal defaultBallad intros, clean verses
Chorus, under a soloSlowShallowSubtleLeads and held bends
Solo delay350-500 ms or a dotted eighth2 to 4 repeats15-25%Leads, long sustained notes
FlangerVery slow sweepModerate regenPedal defaultIntros and accents
Suggested starting points - set them by ear against the record.

Put chorus and delay after the distortion - in the amp's effects loop on a high-gain head - so the repeats stay clean instead of being distorted. Work out the delay time from the song's tempo with the free delay time calculator, and see the modulation pedal guide and the delay pedal guide for each control in detail.

Stereo racks, gates and compression, briefly

By the late 80s, top session and touring players had moved their effects out of pedals and into rack units - TC Electronic's 2290 delay, Eventide harmonizers, Lexicon reverbs - switched from one controller. The idea worth stealing is the wet/dry rig: the amp's dry sound stays in the center, untouched, while delay, chorus and reverb come only from separate speakers to the left and right. The dry tone keeps its punch and the effects spread around it instead of blurring it.

  • Two or three amps: one dry amp in the middle; a stereo chorus or delay, set fully wet, into a second amp or a pair of powered speakers.
  • One amp: put the chorus and delay in the effects loop and keep the mix lower than you would like. You lose the dry center, but the order is right.
  • Modeler: split the path in two, with the dry amp panned center and a fully wet chorus and delay path panned wide.

Gated and compressed

High gain plus a rack full of processors meant noise, so many rigs carried noise reduction, and the records were compressed hard into an even, glossy wall. Tom Scholz's Rockman headphone amp packaged that compressed, chorused sound into a small box, and you can hear it across Boston's Third Stage. On your rig, a gently set noise gate after the drive and a little compression on clean arpeggios get you closer than more gain does.

E♭ tuning and the techniques that sell it

Plenty of 80s records are tuned a half step down. Van Halen's early albums and Guns N' Roses' Appetite for Destruction are the famous cases, and a lot of hair metal followed. Standard tuning still leads, but E♭ is a strong second:

How glam metal guitar parts are tuned
Share of 940+ glam metal guitar tones in the ToneMirror catalog by documented tuning. Tap a tuning for the songs in it.

E♭ standard keeps every chord shape the same, makes wide bends and vibrato easier and darkens the whole band slightly. If you play along a half step off, nothing will sound right however good the tone is - the free online tuner has the alternate tunings built in.

The playing is half the sound

  • Wide, even vibrato on every held note, often from the wrist.
  • Pinch harmonics: let the edge of your thumb graze the string just after the pick hits it, on the bridge pickup with plenty of gain. Move the picking spot to find the squeal.
  • Tapping and legato, the language Van Halen's “Eruption” made standard.
  • Pedal-tone chugs: palm-muted eighth notes on the low string under ringing chords, the engine of most hair metal verses.

Why the records sound so big: stacked doubles

Big-budget 80s rock was built in layers. Rhythm parts were doubled and panned apart, choruses got extra overdubs, and the whole stack was compressed into a dense, even wall. Mutt Lange's productions for Def Leppard are the famous example - Hysteria took years to make, and its guitars are layer upon layer.

  • Each track has less gain than the stack suggests. Dial one guitar for definition, not for the size of the finished record.
  • Vary the doubles. A different guitar, pickup or amp setting on each side fills more of the spectrum than two identical takes.
  • Live, you are one guitar. A touch more mids, a little chorus and a short delay help one amp fill the space two or four tracks filled on the record.

Some hair metal records to practice on:

The shortcut: an 80s song's settings for your rig

Almost nobody owns a hot-rodded 80s Marshall, a superstrat with the right pickup and a stereo rack, and every record used a different mix of them. ToneMirror starts from what a specific recording used and rewrites it for your gear: where your gain and EQ should sit for the same crunch, which pickup and tuning to use, and how to set the overdrive, chorus and delay you already own, in signal-chain order. Modelers get the blocks to build.

Find the song in the tone library, browse the glam metal tone pages, or start from the tone matcher.

Songs to try it on

Each of these has its recorded rig and settings on its own page - open one, then get it translated for your gear.

Frequently asked questions

What amp settings give an 80s rock tone?

On a Marshall-style master-volume amp, start with gain around 6 to 7, bass 4 to 5, mids 6 to 7, treble 6 to 7 and presence around 6. That is hotter than 70s crunch and far less scooped than thrash. Adjust by ear against the record, and add an overdrive as a boost if your amp runs out of gain.

What guitar do I need for hair metal?

Any guitar with a hot bridge humbucker gets you most of the way. Superstrats with a Floyd Rose are the classic look and make dive bombs possible, but plenty of the decade's records were cut on Les Pauls into Marshalls. Single coils work with a little more gain, more mids and a noise gate.

Did 80s rock guitarists use distortion pedals?

Mostly the gain came from the amp - hot-rodded or master-volume Marshalls, Mesa/Boogies and, later in the decade, Soldanos. Pedals pushed the amp harder or added color: overdrives used as boosts, chorus, delay, phaser and flanger.

How do I get the 80s chorus sound?

Use a chorus with a slow rate and moderate depth on clean arpeggios, and a shallower setting under solos. Put it after your distortion, ideally in the amp's effects loop, and run it in stereo if you can. Keep it off the main rhythm riff.

Were 80s rock songs tuned down?

Many were. Van Halen's early albums and Guns N' Roses' Appetite for Destruction are a half step down, in E♭ standard, and a lot of hair metal followed. Most arena rock is in standard tuning, so check the song's tone page before you dial in.

Is there an app that gives 80s rock settings for my gear?

ToneMirror does this song by song. Pick the track, enter the guitar, amp or modeler and pedals you own, and it translates the original rig's settings - gain, EQ, pickup, tuning, chorus and delay - to your setup.

Get settings for my rig